| Product Line | Features | Document(s) |
|---|
| .100" Centerline (Discrete IDC) |
 | - Vertical and right-angle headers
- Connector housings may be stacked end-to-end within one pair of covers
- Receptacles available in plain, polarized, latching and guide ribs
| |
|
| .125 Inch Centerline - AMPMODU Level V |
 | - 0.125 [3.18] centerline
- Housing size 8-40 positions
- Terminates 26-22 AWG [0.12-0.3mm²] discrete wire as well as jacketed cable and boned ribbon cable (conductors separated)
- Double row only
- Pre-loaded IDC receptacle contacts
- Product Options: Snap-on covers with or without cable tie paddles; stackable end-to-end and side-to-side
| |
|
| 1.5mm AMP Mini CT |
 | - Applicable Wire Size: AWG 28-26
- DIP-type post headers feature a staggered tine design
- Two-row type post headers incorporate two receptacle connectors in a holder
| |
|
| 2.5mm Metric Interconnect System |
 | - 2 through 13 positions
- Compact, low-profile 2.5mm pitch
- Crimp type receptacles accept wires of AWG 30-22 with insulation diameters from 1.0-1.9 mm
| |
|
| 2mm AMP CT |
 | - Surface mount and through-hole headers
- Pre-loaded housings available
- Various color options
| |
|
| Ballast Products & LED Interconnections |
 | - Low Profile, SMT wire poke-in connector
- Row-to-row stackable with pads on 4mm centers
- Splice poke-in accommodates two (20) pre-stripped 18 AWG solid wires
- Connector latches prevent unintentional disconnect of connector
| |
|
| CHAMP Connectors |
 | - Industry standard solution
- Contacts on 0.8mm, 1.27mm or 2.16mm centerlines
- Mounting Methods: Right-angle, edge and vertical
| |
|
| IDC Termination (MT EI Series Connectors) |
 | - Contacts accept discrete wire, ribbon cable, laminated ribbon cable, shield drain wire and jacketed cable
- Receptacle housing is preloaded with insulation displacement receptacle contacts
| |
|
| MTA 100 Connectors |
 | - 0.100” centerline spacing
- 2 - 28 position
- Terminates 28-22 AWG discrete wire or notched ribbon cable
- Closed end and feed-through receptacles with and without polarization tabs
- Right-angle and vertical mount headers with friction lock and shroud options
- IDC wire-to-board and wire-to-wire connection system
- 250V, 5A contact rating
- Connector housings are polarized to prevent reverse mating
| |
|
| MTA 156 Connectors |
 | - Connector styles include both closed end and feed-thru, with and without locking ramps and polarizing tabs
- Connectors and headers, except shrouded headers, are end-to-end stackable
- Molded ribs on housing do not allow reverse mating
| |
|
| MTIS (MT Interconnection System) |
 | - Mass termination of several discrete wires or ribbon cable in a single operation
- Contacts with dual leaf cantilever beams
- Posts protected on three sides by housing walls
- High production rates with no rejects
- Crimp snap-in contacts for subsequent wiring changes
- Headers are available in vertical or right-angle flat versions with single row or staggered solder tynes
| |
|
| NECTOR Connector System |
 | - Pluggable electrical installation system
- Three possible contact styles: Spring clamp or screw for field installation, and crimped for mass production
- Locking devices give improved latching between both interconnection sides according to VDE
- Tool removable contact tabs according to VDE
| |
|
| Pivot Connectors |
 | - Eliminates need for a tool for termination - just use your finger
- Small size and tool-less capability make it perfect for space constrained applications
- Terminate wires from either side of the connector or pass wires completely through for bridging connections
- Perfect for field-installed products; IDC contacts eliminate need to strip wires
| |
|
| Standard Timer (AMP RAST 5 Appliance) Connectors |
 | - Suitable for high-density and high-current carrying requirements
- Vertical and right-angle versions available in 2 through 8 positions
- 6.35 x 0.81 [.250 x .032] FASTON tabs built on 5 mm centerlines
- Fully assembled and is easily press fit into the board
| |
|
